Search results

• Tire code
  == Tire geometry ==
  6 KB (994 words) - 10:32, 25 September 2009
• VR6 engine
  ...figuration can also be described as a "Staggered Six", in keeping with the geometry of the Lancia Fulvia staggered-four developed in the late 1950s. Staggered ...to Schrick who redesigned it and offered it as the Schrick VGI ("Variable Geometry Intake").
  13 KB (2,025 words) - 21:40, 16 July 2008
• Piston
  ...a sliding [[plug]] that fits closely inside the [[bore]] of a [[cylinder (geometry)|cylinder]].
  2 KB (354 words) - 08:11, 8 October 2009
• Jake brake
  ...ust and/or stator travel beyond the normal operating range on the variable-geometry turbocharger to produce engine braking without the noise associated with a
  4 KB (557 words) - 08:52, 9 August 2009
• De Dion tube
  ...tly connected to the [[chassis]] nor is it intended to flex. In suspension geometry it is close to the [[beam axle|trailing beam suspension]] most recently see
  3 KB (488 words) - 22:47, 23 September 2009
• Pushrod
  ...[[David Dunbar Buick]]. It employs [[pushrod]]-actuated valves [[parallel (geometry)|parallel]] to the [[piston]]s and this is still in use today. This contras ...as much greater freedom of component placement and intake and exhaust port geometry. Most modern pushrod engines have two valves per cylinder, while many OHC e
  8 KB (1,302 words) - 08:11, 14 June 2009
• Unsprung weight
  ...irregularities of the road surface will transfer to the cabin through the geometry of the suspension and hence ride quality is deteriorated.
  4 KB (675 words) - 21:35, 31 July 2009
• Torelli
  ...stage-racing geometry. Please see the chart at the bottom of the page for geometry specifics. The fork uses our standard investment-cast Walter B-41 fork crow
  5 KB (631 words) - 10:50, 8 October 2009
• Bandini 1000
  ...] in this vein is considered the change in the distribution of weights and geometry of suspensions that resulted in new mergers of portamozzi.
  4 KB (615 words) - 22:30, 23 September 2009
• Multi-link suspension
  It is very hard to optimise the geometry without a full 3d analysis, and compliance effects are important.
  3 KB (519 words) - 16:52, 26 October 2009
• Nicola Romeo
  ...d industrial engineer Romeo is occupied in the scientific problems of pure geometry. It was also very active in charitable works and founded and supported a ki
  5 KB (768 words) - 15:26, 13 April 2009
• Front-wheel drive
  ...the lengths of unequal front drive shafts. However, Center-point steering geometry can be incorporated in the design to avoid torque steer. This is how the po * Due to geometry and packaging constraints, the CV joints ([[constant-velocity joint]]s) att
  12 KB (1,842 words) - 23:38, 7 August 2009
• Roller bearing
  ...radial]] ([[perpendicular]] to the shaft) and [[axial]] loads ([[parallel (geometry)|parallel]] to the shaft). For lightly-loaded bearings, balls offer lower
  13 KB (2,121 words) - 07:16, 6 July 2009
• Lancia Kappa
  ...ineup. The naturally-aspirated 2.0 L engine is fitted with a variable geometry inlet [[manifold]]. Inside the cabin, the seats are replaced by a new desig * uprated to 155 PS in 1996, after the addition of a variable geometry inlet [[manifold]], called the Variable Intake System ('''V.I.S''') by Lanc
  8 KB (1,121 words) - 10:49, 18 October 2009
• Flat-twin
  ...motorcycles, as do [[IMZ-Ural|Ural]] and [[Dnepr (motorcycle)|Dnepr]]. The geometry gives good [[Engine balance|primary balance]], but there is an unbalanced m
  4 KB (576 words) - 12:50, 11 May 2010
• Rotary combustion engine
  ...ear on the spindle. The rotor is positively located by the spindle and the geometry of the rotor and engine chamber. There is still some vibration, as while th
  7 KB (1,137 words) - 20:22, 22 September 2009
• Fiat 130
  ...and a limited-slip differential. It is noteworthy that the rear suspension geometry can be finely tuned.
  8 KB (1,123 words) - 15:35, 31 October 2009
• Bandini 1000 P
  ...rtant novelty but also the return to the final four-wheel independent. The geometry of the rear suspension, tested on a copy of ''[[Bandini formula junior | Fo
  5 KB (755 words) - 22:29, 23 September 2009
• Michael Doohan
  ...yed a large part in his success, his ability to perfect the suspension and geometry of a racing motorcycle gave him an enormous advantage over his rivals, even
  4 KB (651 words) - 19:51, 27 September 2009
• Colnago
  ...vel aluminum road bike models from Giant, made to Colnago's spec and frame geometry and for sales in Europe and Asia only. All other Colnago bicycles are assem
  7 KB (1,076 words) - 15:41, 14 May 2009

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)