Search results

• Timing marks
  ...TDC at different times, equal to the [[angular displacement]] between the cylinders. ...patterns are found in almost all [[straight engine]]s with even numbers of cylinders, with the two end pistons and two middle pistons moving together (not neces
  2 KB (366 words) - 13:27, 16 August 2009
• Cylinder bank
  ...re typically arranged with their pistons in rows, moving inside individual cylinders. This allows the [[engine block]] to be built from a single piece of metal,
  548 bytes (87 words) - 17:20, 17 December 2007
• Flat-10
  504 bytes (65 words) - 22:35, 23 September 2009
• V5
  ...ngine]] in [[V engine|V]] [[engine configuration|configuration]] with five cylinders, e.g. as in the [[Honda]] RC211V [[motorcycle]]
  624 bytes (82 words) - 23:25, 14 June 2009
• Monaco-Trossi
  ...s]] arranged in two rows with a single combustion chamber for each pair of cylinders. This was front-mounted and air-cooled like an aero-engine. Another novelty
  1 KB (185 words) - 10:34, 18 November 2011
• W8
  ...one with three banks of cylinders, one with four and one with two banks of cylinders and two [[crankshaft]]s. The classical W engine uses three banks of cylinders, all connected to one [[crankshaft]].
  4 KB (680 words) - 10:30, 27 September 2009
• Straight-12
  678 bytes (103 words) - 21:56, 17 August 2009
• Flat-8
  759 bytes (101 words) - 23:45, 20 September 2009
• Flat-H
  ...ion is to allow the building of reasonably short engines with more than 12 cylinders, their compact size being useful as [[aircraft engine]]s where their small
  3 KB (449 words) - 12:23, 15 July 2008
• SAL
  ...HP 3.7-liter four-cylinder engine [[Monobloc]], while the 40hp Esperia had cylinders cast in pairs. Despite some race successes in the 20hp car, the SAL company
  733 bytes (103 words) - 14:14, 11 June 2009
• Straight-8
  ...Mans]] fame the camshaft drive had been moved to the engine center between cylinders # 4 and 5, thus reducing the aforementioned limitations.
  2 KB (352 words) - 17:22, 13 June 2009
• Straight-14
  1,022 bytes (156 words) - 00:30, 23 June 2009
• Straight-3
  ...since the three cylinders are offset from each other the firing of the end cylinders induces a rocking motion from end to end. The use of a [[balance shaft]] i ...ke a 360° [[straight-2]]. The inner cylinder is offset 180° from the outer cylinders. In these engines cylinder 1 fires, 180° later cylinder 2 fires, and then
  2 KB (349 words) - 12:22, 8 October 2009
• Dall'Oglio
  ...to the Trade Fair in Milan the same year. The 125 cc engine had cast iron cylinders with the head made of bronze and a two speed gearbox.
  975 bytes (139 words) - 16:10, 25 June 2009
• Berneg
  ...on to the camshaft in the head which was controlled by a double chain. The cylinders were made of cast iron, as the only thing not lightend. The gear change in
  2 KB (274 words) - 21:41, 26 June 2018
• Magliano
  ...The tubed frame had a telescopic front fork and rear shock absorbers with cylinders. The rear wheel had disc brakes. The bike had only a front fairing and a pa
  1 KB (158 words) - 19:44, 15 June 2009
• Square engine
  The engine is only referred to as "square" when four cylinders are utilised, otherwise the engine is a [[U engine]].
  1 KB (168 words) - 16:17, 13 June 2009
• Lamborghini V10
  ...It is a 90° [[V10]] which is unusual for this particular configuration of cylinders. It was chosen to keep the [[center of gravity]] of the engine low. For t ; Cylinders : Bore × stroke 82.5 mm x 92.8 mm (0.89 ratio), 496 cc/cylinder, aluminium
  2 KB (284 words) - 11:38, 8 October 2009
• Flat-16
  ...nternal combustion engine in [[flat engine|flat]] configuration, having 16 cylinders.
  669 bytes (99 words) - 23:04, 10 May 2010

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)