Search results
Jump to navigation
Jump to search
- ...a bank, or 'block'. A cylinder block is typically [[casting|cast]] from [[aluminum]] before precision features are machined into it. The cylinders are then li3 KB (441 words) - 19:45, 31 March 2009
- ...]] Zagato V4 and the 1958 – 1960s [[Lancia Flaminia]] Zagato V6, both with aluminum bodies designed and built by Zagato, and the 1967-1972 [[Lancia Fulvia]] Za2 KB (331 words) - 08:03, 18 September 2009
- ...the introduction of the [[Kool-Bore]] (all aluminum) and [[Sleeve-Bore]] (aluminum, with a [[cast iron]] cylinder liner).6 KB (905 words) - 08:43, 8 October 2009
- ...cia Lambda|Lambda]] from [[1922]] through [[1931]]. It was a narrow-angle aluminum design. All three displacements shared the same long 120 mm stroke, a4 KB (612 words) - 16:37, 13 June 2009
- ...a bank, or 'block'. A cylinder block is typically [[casting|cast]] from [[aluminum]] or [[cast iron]] before precision features are machined into it. The cyli3 KB (492 words) - 00:06, 8 August 2009
- ...ng unusual combinations of materials (such as glass and stone, plastic and aluminum, plush fabric and chrome, etc.). Two of these designs include stylish [[too3 KB (516 words) - 07:56, 16 July 2009
- ...ld be raised at the flick of a switch. Five pre-production prototypes with aluminum chassis were built, followed by eight with composite chassis. Following the3 KB (450 words) - 22:58, 7 August 2009
- ...k>Alfa Romeo RL Super Sport with [[Carrozzeria Castagna|Castagna]] brushed aluminum body3 KB (390 words) - 09:16, 31 May 2009
- ...]] rear suspension, and [[limited slip differential]] were also used. The aluminum body, designed by [[Bertone]], was a 2-seater. A single [[spyder]] version2 KB (279 words) - 15:31, 11 November 2009
- and the [[aluminum]] body was by [[Medardo Fantuzzi]].2 KB (257 words) - 21:01, 19 October 2009
- ...ed in [[Ferrara]] and active in 1953 and into the 1960's, making primarily Aluminum bodies for [[O.S.C.A.|OSCA]]. Of the some 200 cars produced by [[OSCA]], pe2 KB (313 words) - 23:22, 17 December 2016
- |Chassis || Aluminum |Bodywork || Aluminum, hand made4 KB (663 words) - 16:16, 7 January 2013
- A recent production vehicle using this suspension using an [[aluminum]] tube with leaf springs was the [[Ford Ranger EV]]. The earliest productio3 KB (488 words) - 22:47, 23 September 2009
- ...T for Typo Tubulari (or some reports say Typo Tedesco) because the tubular aluminum chassis was used by Porsche. Somebody thought that if they copied the tubul5 KB (808 words) - 10:00, 26 April 2010
- ...2991 cc, with valves in the head, three marches forward, crank and piston aluminum, and 80 hp power at 4500 rpm.2 KB (344 words) - 13:13, 8 July 2010
- **Aluminum crankset **Aluminum crankset8 KB (1,167 words) - 09:51, 9 October 2009
- ...bare-bones version of the 360 Modena. All have eight-cylinder engines and aluminum chassis. The 360 was replaced by the [[Ferrari F430]] in [[2005]]. ...8 engine; it is the first production Ferrari to be constructed entirely of aluminum. Its six-speed gearbox is available as a manual or [[Formula One|F1]] elect6 KB (804 words) - 10:35, 15 March 2010
- ...ing cars made by [[Maserati]] of [[Italy]], built by [[Giulio Alfieri]], [[aluminum]] body design by [[Medardo Fantuzzi]], both Maserati engineers.2 KB (276 words) - 21:02, 19 October 2009
- ...a Junior]] car using a [[Peugeot]] engine (1960), and was followed by 21 [[aluminum]]-bodied Intermeccanica-[[Puch]] (IMP) 500ccm-engined cars, of which one wo Powered by the factory-correct Buick 310 Wildcat V-8 w/polished aluminum heads and alum, 4 bbl. intake manifold. A Borg/Warner T-10 4spd and Dana-446 KB (727 words) - 21:00, 19 August 2011
- |Chassis/body || aluminum body on sheet-metal frame chassis2 KB (271 words) - 19:10, 19 October 2009