Search results

• Babbitt metal
  ==Traditional babbitt bearings== ...ted through the factory floor via overhead shafting running in hundreds of bearings of this form.
  4 KB (740 words) - 23:31, 3 July 2009
• Short block
  ...fication. The crankshaft is installed in the cylinder block using new main bearings and thrust washers, and the main bearing caps are torqued to specification. ...ent, twisted or cracked. They are installed on the crankshaft with new rod bearings, and the rod bearing caps are torqued to specification.
  2 KB (278 words) - 22:48, 11 June 2009
• Roller bearing
  ...ct-bearing din628 type-qj 180-ex.png|thumb|300px|Four-point-contact radial bearings]] ...bearing (mechanical)|bearing]]s" for more on the historical development of bearings.
  13 KB (2,121 words) - 07:16, 6 July 2009
• Fully Integrated Robotised Engine
  Mechanically they are simple [[straight-4]] engines with five bearings and [[overhead cam]] heads.
  831 bytes (122 words) - 08:13, 8 October 2009
• Crankshaft
  ...[[straight-8]] engines. High performance engines will often have more main bearings than their lower performance cousins, for this reason. In addition, to conv
  7 KB (1,012 words) - 23:56, 20 September 2009
• Bushing
  2 KB (276 words) - 15:07, 9 August 2009
• Parasitic loss
  ...engine]] almost everything including the driveline causes parasitic loss. Bearings, oil pumps, piston rings, valve springs, flywheels, transmissions, drivesha
  2 KB (243 words) - 08:26, 8 October 2009
• Straight-8
  2 KB (352 words) - 17:22, 13 June 2009
• Bugatti Type 35
  This new powerplant featured five main bearings with an unusual [[ball bearing]] system. This allowed the engine to rev to ...a famous maker of imitation jewelery. The Tecla's engine used three plain bearings, smaller valves, and coil ignition like the [[Bugatti Type 30|Type 30]]. W
  5 KB (747 words) - 23:59, 5 November 2009
• BMP
  ...[[engine]], transmission gearbox was a 4-speed with gears mounted on ball bearings and a transmission belt. The rigid frame that cradled with a closed fork tu
  2 KB (258 words) - 12:40, 1 July 2010
• Alfa Romeo RL
  ...rsion of RL and it weighted half of normal versions, engine had seven main bearings instead of four and double carburetos.
  3 KB (390 words) - 09:16, 31 May 2009
• Automotive terms Italian to English
  | Rod bearings | Main bearings
  5 KB (629 words) - 10:22, 6 December 2012
• Molaroni
  ...inder and piston were rod iron and on the steel to nickel head, the roller bearings and crankshaft were one piece. The transmission was a Sturmey-Archer two-sp
  2 KB (337 words) - 13:18, 21 January 2011
• Kingpin
  ...degrees of freedom of motion of the rest of the front suspension. When its bearings were replaced starting in the 1950s by ball joints, more complicated suspen
  3 KB (429 words) - 14:44, 12 November 2009
• Bandini 1000 GT
  ...inium]] a chamber burst hemisphere, distribution mixed chain and gears on bearings , oblock and [[base]] to five [[media bench]] in a single casting and sump
  4 KB (501 words) - 22:28, 23 September 2009
• Unsprung weight
  4 KB (675 words) - 21:35, 31 July 2009
• Lancia Aurelia
  ...rear suspension. The engine was changed from white metal bearings to shell bearings. An open car, the B24 Spider was introduced at this time (1954 to 1955) and
  7 KB (1,029 words) - 01:50, 12 December 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)