Search results

• Ercoli-Cavallone
  ...r [[cylinder]] it had a better cooling. The change is sliding block with [[gears]], the [[transmission]] is made up of a primary and secondary chain. The [[
  1 KB (179 words) - 16:46, 30 March 2009
• Altea
  ...[[cubic centimeter|cc]] valve side fly outside and exchange in bulk three gears, which followed a 200 cc bike with valves in the head, [[distribution |(mec
  1 KB (170 words) - 21:55, 17 August 2009
• Kinematic pair
  1 KB (144 words) - 23:53, 20 September 2009
• Derailleur gears
  ...sprocket to another. Although widely referred to as "[[gear]]s", bicycle "gears" should properly be referred to as '''sprockets''' since they are driven by Some early designs used a system of rods to move the chain onto various gears.
  11 KB (1,674 words) - 23:29, 3 July 2009
• Sequential manual transmission
  ...ng]], where [[gear]]s are selected in order, and direct access to specific gears is not possible. ...e to complete a shift into any adjacent gear. This allows shifting between gears without the use of the clutch. The clutch would normally be used only for s
  7 KB (1,143 words) - 23:27, 3 July 2009
• Transmission Control Unit
  ...by the [[Engine Control Unit]] to calculate how and when to change [[Gears|gears]] in the vehicle for optimum performance, [[Fuel efficiency|fuel economy]] ...matic transmission have electrical solenoids which are activated to change gears. These solenoids range from very simplistic control in older automatic tra
  5 KB (656 words) - 09:01, 8 October 2009
• Variomatic
  ...s introduced on the [[DAF 600]]. Because the system does not have separate gears, but one (continuously shifting) gear and a separate 'reverse mode' (as opp ...tronic]]. This system uses a metal belt and lacks a limit to the number of gears available, switching between them without noticeable shocks. These metal dr
  5 KB (710 words) - 23:28, 3 July 2009
• Cagiva SXT
  ...of content, as were the content consumption of oil and gasoline, while the gears were well spaced between them and at the same time long, so by not having t
  1 KB (234 words) - 23:33, 28 January 2009
• Bicycle gearing
  ...ar ratios for optimum efficiency or comfort. Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi-speed bic ...inring of the crankset and the rear cog or sprocket. or the ratio of bevel gears on a [[shaft-driven bicycle]]. In the case of a derailleur-equipped bicycle
  24 KB (3,509 words) - 23:29, 3 July 2009
• Simonini
  ...lta'' and the ''Shadow'' 125 normale, used the new engine Sachs with seven gears and the brakes were disc both in front and in the rear. Over time, difficul ...e'' still using the engine Sachs that was identical to the 250 cc to seven gears version. The ''Mustang'' was also used to race, while Witteven Jan has been
  4 KB (590 words) - 18:04, 6 July 2009
• Lancia Eta-30/50HP
  ...cylinder) operated by a [[camshaft]] side (in the basement) operated by [[gears]]; crankshaft on three media, [[compression ratio]] 5:1, [[power (physics)| ...rd, direct (1 : 1) in the fourth, reversing 3521:1; final reduction (bevel gears) 3600:1 (15/54), available also the following other reports 3267:1 (15/49),
  4 KB (553 words) - 21:23, 27 April 2009
• Ambrosini
  *4 gears
  832 bytes (112 words) - 22:45, 30 March 2010
• Cappa
  ...er engine which was at that time still a novelty. There were already three gears, a shaft drive, dual magneto and a tank for gasoline and water on board.
  969 bytes (141 words) - 16:52, 14 April 2010
• Bandini 1100
  ...mpulsorily amended as well as [[camshaft | camshafts]], it was a chain and gears. ...ngine, 2 inclined valves per cylinder, 2 camshafts controlled by chain and gears
  5 KB (619 words) - 22:26, 23 September 2009
• Long block
  ...t engines, the [[camshaft]] will be installed. On many engines with timing gears, the camshaft will be timed.
  876 bytes (131 words) - 08:51, 8 October 2009
• Motron
  ...le brand, such as the SA 50, the RAG I the MST 50, the Taxi, all with four gears, like the GTO el'Oregon.
  1 KB (163 words) - 22:21, 18 April 2010
• Lambretta (company)
  ...t handgrip while pulling the clutch lever and selecting between the 3 or 4 gears. They also have had [[two-stroke cycle|two stroke]] [[motor]]s, requiring a ...t handgrip while pulling the clutch lever and selecting between the 3 or 4 gears. They also have had two stroke motors, requiring a mixture of oil with the
  4 KB (584 words) - 21:50, 17 August 2009
• Short block
  ...engines, the [[camshaft]] may also be installed. If the engine uses timing gears, they may be installed and timed.
  2 KB (278 words) - 22:48, 11 June 2009
• Azzariti
  ...anks at 360 ° and the distribution of two camshafts in the head, driven by gears. The displacement was 343.99, with bore and stroke at 62 x 57 mm. It appear
  1 KB (143 words) - 23:59, 6 February 2011
• Transmission
  ...nt [[gear ratio]]s. In this case, most of the gear ratios (simply called "gears") are used to slow down the output speed of the engine and increase torque. ...and mining equipment. In addition to ordinary transmission equipped with gears, such equipment makes extensive use of the [[#Hydrostatic transmission|hydr
  12 KB (1,865 words) - 06:22, 26 September 2016

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)